The Effect of Cooling Media on Tensile Strength of Medium Carbon Steel in Post Welding Process Using Electric Welding (SMAW) with E7018 Electrodes
DOI:
https://doi.org/10.24036/teknomekanik.v3i2.6472Keywords:
Cooling Medium, Tensile Strenght, SMAW, Medium Carbon Steel, Electrode E7018Abstract
The use of cooling media in post welding process will affect the tensile strength of a material. This study aims to determine how much the influence of using cooling media in post welding and which cooling media is appropriate to use. The process is done by comparing the tensile strength of each cooling media, namely the cooling media of water, air, and coolant. The use of cooling media is carried out after the welding process, until the material that is ready to be welded reaches room temperature. Based on the experiments that have been conducted, the use of post-welding cooling media affects the tensile strength of medium carbon steel with the highest effect on the water cooling media, then the coolant media, and the lowest is the air cooling media. Therefore, the choice of the use of cooling media significantly affects the tensile strength of medium carbon steel in the post-welding process.
Downloads
References
Verma, Jagesvar & Taiwade, Ravindra. Effect of welding processes and conditions on the microstructure, mechanical properties and corrosion resistance of duplex stainless steel weldments—A review. Journal of Manufacturing Processes. 2017; 25: 134-152. 10.1016/j.jmapro.2016.11.003.
Talabi, S. I., O. B. Owolabi, J. A. Adebisi and T. Yahaya. Effect of welding variables on mechanical properties of low carbon steel welded joint. Advances in Production Engineering & Management. 2014; 9:181-186.
Çelik, S. and I. Ersozlu. Investigation of the mechanical properties and microstructure of friction welded joints between AISI 4140 and AISI 1050 steels. Materials & Design. 2009; 30(4): 970-976.
K. Y. Chang, Y.C. Lin. Elucidating the microstructure and wear behavior of tungsten carbide multi-pass cladding on AISI 1050 steel. Journal Material Processing Technology. 2010 ; 210(2): 219–225. doi: 10.1016/j.jmatprotec.2009.09.003.
D. Setyawan. Analisa Pengaruh Media Pendingin Pada Proses Perlakuan Panas Terhadap Kekuatan Tarik Material ST 41. Simki-Techsain. 2017; 1(2): 16–24.
W. Hui, Y. Zhang, C. Shao, S. Chen, X. Zhao, and H. Dong. Effect of Cooling Rate and Vanadium Content on the Microstructure and Hardness of Medium Carbon Forging Steel. Journal of Material Science & Technology. 2016; 32(6): 545–551., doi: 10.1016/j.jmst.2016.01.006.
Baday.Şehmus, Başak.Hüdayim & Gural, A. Analysis of spheroidized AISI 1050 steel in terms of cutting forces and surface quality”. Metallic Materials. 2016; 54: 315-320. 10.4149/km_2016_5_315.
Xu, Xuanxi & You, G. & Ding, Yuhan & Tong, Xin & Zai, Le & Liu, Qing. Microstructure and mechanical properties of inertia friction welded joints between high-strength low-alloy steel and medium carbon steel. Journal of Materials Processing Technology. 2020; 286. 116811. 10.1016/j.jmatprotec.2020.116811.
Esther T. Akinlabi, Kazeem O. Sanusi. Experiment on Effect of heat treatment on mechanical and microstructure properties of AISI steel. Material. Today Proceding. 2018; 5(9) : 17996–18001. doi: 10.1016/j.matpr.2018.06.132.
Abdulmumin Akoredeley Alabi, Peter Bitrus Madakson, Danjuma Saleh Yawas and Terver Ause. Effect of postweld heat treatment on the mechanical properties of weld in a medium carbon steel. Journal of Mineral and Material Characterization and Engineering. 2013; 1: 131–137, 2013, doi: 10.4028/www.scientific.net/AMM.315.6.
AISI Standart. S100-16. North American Specification for the Design of Cold-Formed Steel Structural Members - 2016 Edition with Supplement 1. American Iron Steel Institute., 2016.
Zulkifli, B. Dahlan, N. Fatimah. Analisa Pengaruh Variasi Media Pendingin Terhadap Kekuatan Mekanik Pada Hasil Pengelasan Metode Smaw Material Baja St 52. Journal of Welding Technology. 2020; 1(2) : 48–51.
D. Pathak, Rudra P. Singh, S. Gaur and Vincent Balu. Experimental investigation of effects of welding current and electrode angle on tensile strength of shielded metal arc welded low carbon steel plates. Material Today : Proceeding. 2019 ; 26: 929–931. doi: 10.1016/j.matpr.2020.01.146.
Sayed, Aamir, Devesh Kumar, Gulshan Shahare, Nitin Nawkhare, Rushikesh Bhanarkar, Durgesh Dhande, Atul Ramteke and Usha Bharadkar. Mechanical and microstructural testing of C-45 material welded by using SMAW and GMAW process. Materials Today: Proceedings.2020. 10.1016/j.matpr.2020.07.036.
Tarkono, Gabe. P. Siahaan, Zulhanif. Studi Penggunaan Jenis Elektroda Las Yang Berbeda Terhadap Sifat Mekanik Pengelasan SMAW Baja AISI 1045. Jurnal Mechanical. 2012; 3(2): 51–62.
R. Paventhan, P. R. Lakshminarayanan, and V. Balasubramanian. Optimization of Friction Welding Process Parameters for Joining Carbon Steel and Stainless Steel. Journal of Iron and Steel Research International. 2012; 19(1): 66–71, 2012, doi: 10.1016/S1006-706X(12)60049-1.
J. K. Odusote, T. K. Ajiboye, and A. B. Rabiu. Evaluation of Mechanical Properties of Medium Carbon Steel Quenched in Water and Oil. Journal of Mineral and Material Characterization Engineering. 2012; 11(09): 859–862, 2012, doi: 10.4236/jmmce.2012.119079.
Subagiyo, Samsul Hadi, Lisa. A dan Hari.R . Analisis Kekuatan Tarik Dan Kekerasan Baja Tahan Karat Martensitik Hasil Pengelasan Dengan Variasi Laju Pendinginan. Jurnal Ilmiah Teknologi FST Undana, 2019;13(2) :1–5.
Sri Nugroho, Gunawan.D Haryadi. Pengaruh Media Quenching Air Tersirkulasi (Circulated Water) Terhadap Struktur Mikro Dan Kekerasan Pada Baja Aisi 1045. Jurnal Rotasi, 2005; 7(1):19–23.
Dicky Adi Tyagita, Andik Irawan. Kekuatan Tarik Hasil Pengelasan Smaw Plat Baja St 37 Dengan Pendingin Liquid. Jurnal Ilm INOVASI. 2016; 1(3):180–186.
Min Shan Htun, Si Thu Kyaw and Kay Thi Lwin. Effect of heat treatment on microstructures and mechanical properties of Spring Steel. Journal of Metal, Material and Mineral. 2008; 18(2): 191–197. doi: 10.1080/02670836.2018.1465620.
Harsono Wiryosumarto, Teknologi Pengelasan Logam. Jakarta: Pradnya Paramita, 2008.
M. Kimura, K. Ohara, M. Kusaka, K. Kaizu, and K. Hayashida. Effects of Tensile Strength on Friction Welding Condition and Weld Faying Surface Properties of Friction Welded Joints Between Pure Copper and Austenitic Stainless Steel. Journal of Advanced Joining Process., 2020; 2: 100028. doi: 10.1016/j.jajp.2020.100028.
Mohammad Raffik bin Khiyon, Salwani Mohd Salleh. Effect of heat-treatment on the hardness and mechanical properties of Boron Alloyed Steel. MATEC Web of Confrence., 2016; 90. doi: 10.1051/matecconf/20179001014.
Ratnesh Shing, Rajesh Prasad, Sunil Pandey & Shatis Sharma. Effect of Cooling Environment and Welding Speed on Fatigue Properties of Friction Stir Welded Al-Mg-Cr Alloy”.International Journal of Fatigue. 2019; 127 : 551-563.
Jhon. W. Creswell, Research Design (Pendekatan Metode Kualitatif, Kuantitatif, dan Campuran). 2016.
Jasman, J., Irzal, I., Adri, J., & Pebrian, P. Effect of Strong Welding Flow on the Violence of Low Carbon Steel Results of SMAW Welding with Electrodes 7018. Teknomekanik, 2018 ; 1(1): 24-31. https://doi.org/10.24036/tm.v1i1.972
ASTM E8, “ASTM E8/E8M standard test methods for tension testing of metallic materials,” Annual Book ASTM Standart 4, 2010, doi: 10.1520/E0008.
Bondan T Sofyan, Pengantar Material Teknik, 1st ed. Jakarta: Salemba Teknika, 2010.
Basuki Widodo, Aladin E. Purkuncoro. Penggunaan Elektrode E 7016 Pada Baja AISI 1050 Terhadap Sifat Mekanik Dengan Variasi Posisi Pengelasan SMAW,” Jurnal FLYWHEEL, 2017;8(1):36–44, 2017.
F. Yusman,. Pengaruh Media Pendingin Pada Proses Quenching Terhadap Kekerasan Dan Strukur Mikro Baja AISI 1045,” 2018
