The effect of T6 heat treatment on the tensile, impact, and fatigue properties of Al6061-fly ash composites
DOI:
https://doi.org/10.24036/teknomekanik.v9i2.50672Keywords:
Al6061, fly ash, T6 heat treatment, tensile strength, impact energy, fatigue strengthAbstract
This study investigates the effect of controlled precipitation hardening on the mechanical behavior of Al6061–fly ash metal matrix composites fabricated using stir casting and subjected to T6 heat treatment. The specimens underwent solution treatment at 510°C for 1 and 2 hours, followed by oil quenching and artificial aging at 120°C, 140°C, and 160°C for 2 hours. Tensile, Rockwell hardness, impact, and fatigue tests were used to assess the mechanical characteristics, in accordance with ASTM standards, and were supported by microstructural and SEM studies. The findings indicate that T6 treatment greatly improves strength and fatigue tolerance compared with the untreated state. The highest tensile strength and impact energy were achieved under the T6-A2 condition (510 °C for 2 h + aging at 120 °C for 2 h), whereas the longest fatigue life was obtained under the T6-B1 condition (510 °C for 1 h + aging at 140 °C for 2 h). This shows a good balance between strength and toughness, which is related to the formation of fine Mg2Si precipitates and enhanced interfacial bonding. Aging at 120°C resulted in the highest hardness at 510°C (2 hours). Over-aging reduced ductility and impact resistance because of precipitate coarsening. For durable aluminum–fly ash composites, these results show a distinct link between processing, microstructure, and material characteristics.
References
D. B. Miracle, “Metal matrix composites - From science to technological significance,” Compos. Sci. Technol., vol. 65, no. 15-16 SPEC. ISS., pp. 2526–2540, Dec. 2005, https://doi.org/10.1016/j.compscitech.2005.05.027
K. Muqtadar Ali Khan, V. V.D. Sahithi, and K. Vijaya Krishna Varma, “Experimental investigation of mechanical and fracture behaviour of casted alumina (AA6061-SiC-flyash) metal matrix composites,” in Materials Today: Proceedings, Elsevier Ltd, 2021, pp. 528–538. https://doi.org/10.1016/j.matpr.2020.10.742
O. O. Barah, I. Bori, A. J. Otaru, and Z. A. A. A. Zaid, “Processing Optimization of Sustainable AA6061–Fly Ash Composites by Compocasting,” ACS Omega, vol. 11, no. 4, pp. 6647–6656, Feb. 2026, https://doi.org/10.1021/acsomega.5c11742
P. P. Ikubanni, M. Oki, A. A. Adeleke, and P. O. Omoniyi, “Synthesis, physico-mechanical and microstructural characterization of Al6063/SiC/PKSA hybrid reinforced composites,” Sci. Rep., vol. 11, no. 1, Dec. 2021, https://doi.org/10.1038/s41598-021-94420-0
U. R. Kanth, P. S. Rao, and M. G. Krishna, “Mechanical behaviour of fly ash/SiC particles reinforced Al-Zn alloy-based metal matrix composites fabricated by stir casting method,” Journal of Materials Research and Technology, vol. 8, no. 1, pp. 737–744, Jan. 2019, https://doi.org/10.1016/j.jmrt.2018.06.003
Z. A. Karmo Main and A. E. Ismail, “Potential Applications of Fly-Ash and Sisal Hybrid Fibre Reinforced Plastic Composites,” International Journal of Engineering Trends and Technology, vol. 68, no. 7, pp. 34–41, 2020, https://doi.org/10.14445/22315381/IJETT-V68I7P206S
R. J. Shetty et al., “Effect of metallic reinforcement and mechanically mixed layer on the tribological characteristics of Al-Zn-Mg alloy matrix composites under T6 treatment,” Cogent Eng., vol. 10, no. 1, 2023, https://doi.org/10.1080/23311916.2023.2200900
N. Nanjayyanamat, R. Sugandhi, and S. Balanayak, “Mechanical Properties of Fly Ash Reinforced Aluminium 6061 Composite,” IOSR Journal of Mechanical and Civil Engineering, pp. 55–59, 2011, [Online]. Available: https://www.iosrjournals.org/iosr-jmce/papers/Conf-17026-2017/Volume-3/11.%2055-59.pdf
J. David Raja Selvam, D. S. Robinson Smart, and I. Dinaharan, “Microstructure and some mechanical properties of fly ash particulate reinforced AA6061 aluminum alloy composites prepared by compocasting,” Mater. Des., vol. 49, pp. 28–34, 2013, https://doi.org/10.1016/j.matdes.2013.01.053
A. M. Razzaq, D. L. Majid, M. R. Ishak, and U. M. Basheer, “Effect of fly ash addition on the physical and mechanical properties of AA6063 alloy reinforcement,” Metals (Basel)., vol. 7, no. 11, Nov. 2017, https://doi.org/10.3390/met7110477
S. A. Sajjadi, H. R. Ezatpour, and H. Beygi, “Microstructure and mechanical properties of Al-Al2O3 micro and nano composites fabricated by stir casting,” Materials Science and Engineering: A, vol. 528, no. 29–30, pp. 8765–8771, 2011, https://doi.org/10.1016/j.msea.2011.08.052
M. Kok, “Production and mechanical properties of Al2O3 particle-reinforced 2024 aluminium alloy composites,” J. Mater. Process. Technol., vol. 161, no. 3, pp. 381–387, Apr. 2005, https://doi.org/10.1016/j.jmatprotec.2004.07.068
A. Baradeswaran and A. Elaya Perumal, “Study on mechanical and wear properties of Al 7075/Al2O 3/graphite hybrid composites,” Compos. B Eng., vol. 56, pp. 464–471, 2014, https://doi.org/10.1016/j.compositesb.2013.08.013
C. S. Tsao, C. Y. Chen, U. S. Jeng, and T. Y. Kuo, “Precipitation kinetics and transformation of metastable phases in Al-Mg-Si alloys,” Acta Mater., vol. 54, no. 17, pp. 4621–4631, Oct. 2006, https://doi.org/10.1016/j.actamat.2006.06.005
K. Choi, S. Lee, and D. Bae, “Natural and Artificial Aging Effects on the Deformation Behaviors of Al–Mg–Zn Alloy Sheets,” Materials, vol. 17, no. 18, Sep. 2024, https://doi.org/10.3390/ma17184478
M. I. A. Habba et al., “Microstructural evolution and strengthening mechanisms in Cu-coated cBN reinforced aluminum nanocomposites,” Journal of Materials Research and Technology, vol. 38, pp. 3291–3309, Sep. 2025, https://doi.org/10.1016/j.jmrt.2025.08.113
H. Seputro, S. R. Bintoro, D. Ariawan, E. Surojo, and Triyono, “Enhancing AA6061–Bottom Ash Composites: Role of Heat Treatment on Properties and Dimensional Stability,” Civil Engineering Journal (Iran), vol. 11, no. 11, pp. 4864–4885, Nov. 2025, https://doi.org/10.28991/CEJ-2025-011-11-023
R. Lazarova, L. Anestiev, Y. Mourdjeva, K. Valuiska, and V. Petkov, “Microstructural Evolution, Strengthening Mechanisms, and Fracture Behavior of Aluminum Composites Reinforced with Graphene Nanoplatelets and In Situ–Formed Nano-Carbides,” Metals (Basel)., vol. 15, no. 3, Mar. 2025, https://doi.org/10.3390/met15030285
H. Jin, D. Tie, and R. Guan, “Precipitation behavior during re-aging of Al-Mg-Si-Cu alloy,” Mater. Des., vol. 220, Aug. 2022, https://doi.org/10.1016/j.matdes.2022.110883
R. Almeida Rodrigues et al., “Effect of Different T6 Heat Treatment Conditions on the Microstructure and Mechanical Properties of Al-7%Si-0.35% Mg (A356) Alloy for Use in Motorcycles,” Metals (Basel)., vol. 15, no. 7, Jul. 2025, https://doi.org/10.3390/met15070692
L. Shyam, K. Sudhir, K. Ajay, P. Lalman, and Aniruddha, “Fabrication and Characterization of Hybrid Metal Matrix Composite Al-2014/SiC/Fly Ash Using Stir Casting Process,” Mater. Today Proc., vol. 49, no. 8, pp. 3155–3163, 2022, https://doi.org/10.1016/j.matpr.2020.11.168
M. Gazizov, C. D. Marioara, J. Friis, S. Wenner, R. Holmestad, and R. Kaibyshev, “Precipitation behavior in an Al–Cu–Mg–Si alloy during ageing,” Materials Science and Engineering: A, vol. 767, Nov. 2019, https://doi.org/10.1016/j.msea.2019.138369
B. H. Lee, S. W. Park, S. K. Hyun, I. S. Cho, and K. T. Kim, “Mechanical properties and very high cycle fatigue behavior of peak-aged AA7021 alloy,” Metals (Basel)., vol. 8, no. 12, Dec. 2018, https://doi.org/10.3390/met8121023
L. F. Demisie et al., “Experimental analysis on the mechanical properties of Al6061 based hybrid composite reinforced with silicon carbide, bagasse fly ash and aloe vera ash,” Discover Applied Sciences, vol. 6, no. 9, Sep. 2024, https://doi.org/10.1007/s42452-024-06192-7
L. Stemper, M. A. Tunes, R. Tosone, P. J. Uggowitzer, and S. Pogatscher, “On the potential of aluminum crossover alloys,” Progress in Materials Science, vol. 124. Elsevier Ltd, Feb. 01, 2022. https://doi.org/10.1016/j.pmatsci.2021.100873
T. S. Liu, B. X. Dong, H. Y. Yang, F. Qiu, S. L. Shu, and Q. C. Jiang, “Review on role of intermetallic and ceramic particles in recrystallization driving force and microstructure of wrought Al alloys,” Journal of Materials Research and Technology, vol. 27. Elsevier Editora Ltda, pp. 3374–3395, Nov. 01, 2023. https://doi.org/10.1016/j.jmrt.2023.10.098
P. X. Zhang, H. Yan, W. Liu, X. L. Zou, and B. B. Tang, “Effect of T6 heat treatment on microstructure and hardness of nanosized Al2O3 reinforced 7075 aluminum matrix composites,” Metals (Basel)., vol. 9, no. 1, Jan. 2019, https://doi.org/10.3390/met9010044
G. Rodríguez-Cabriales et al., “Synergistic Effects of Sub-Micron WC Reinforcement and T6 Heat Treatment on the Evolution of Microstructure and Mechanical Behavior in Al–Cu–Mg Composites Fabricated Through Powder Metallurgy,” Metals (Basel)., vol. 15, no. 11, Nov. 2025, https://doi.org/10.3390/met15111216
H. R. Channar, B. Ullah, M. S. Naseem, J. Akhter, A. Mehmood, and M. Aamir, “Mechanical Properties and Microstructural Investigation of AA2024-T6 Reinforced with Al2O3 and SiC Metal Matrix Composites,” Eng, vol. 5, no. 4, pp. 3023–3032, Dec. 2024, https://doi.org/10.3390/eng5040157
Z. Achmad, E. Santoso, and A. Jalil, “Analysis of The Effect of Cooling Media Variation And Variation of Cooling Media Temperature on T6 Process Solution Treatment on Shape And Propeler Dimension Changes From Coal Based ALUMINUM-ASH Composite Materials,” in SNTTM XVI, 2018. Page. 161-165. https://prosiding.bkstm.org/prosiding/2018/RM-30.pdf
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Zainun Achmad, Al Emran bin Ismail, Harjo Seputro, Eka Marliana (Author)
This work is licensed under a Creative Commons Attribution 4.0 International License.
