Numerical Analysis of Fluid Flow on Cross Flow and Kaplan Turbine Prototype

Authors

  • Purwantono Purwantono Universitas Negeri Padang
  • Ahmad Halim Sidiq Universitas Negeri Padang
  • Irzal Irzal Universitas Negeri Padang
  • Refdinal Refdinal Universitas Negeri Padang

DOI:

https://doi.org/10.24036/tm.v2i1.1972

Keywords:

Cross Flow Turbine, Kaplan Turbin, Fluid Flow, Numerical Analysis, Turbine

Abstract

Based on previous research conducted by Purwantono about the utilization of exhaust flow from a conventional cross-flow turbine prototype that was used as an inlet of tubin Kaplan [1]. This research was carried out to see how the exhaust flow velocity of each tubin before and after was combined into one combination turbine. This numerical based study uses the Ansys 18.0 application by inputting a 3D design from a conventional turbine prototype which was used as the material for this study. The results obtained in this study show the average of outlet velocity in the Kaplan turbine that uses a velocity outlet from a cross flow turbine of 0.3 m / s greater when it is combined, which is 8.33 m / s and after being combined to 0.38 m / s. The results of this study are expected to contribute to the development of conventional turbines later

Downloads

Download data is not yet available.

References

Purwantono, Syahrul, and J. Adri, “Pengaruh Perubahan Debit Aliran Terhadap Putaran Turbin Banki dan Kaplan,” INVOTEK J. Inov. Vokasional dan Teknol., vol. 18, no. 1, pp. 13–18, 2018.

W. Friska, “No Title,” 23 January, 2013. [Online]. Available: https://www.scribd.com/doc/121931390/MAKALAH-ENERGI-docx. [Accessed: 17-Jan-2018].

Arwizet, “Mesin destilasi pengolahan sampah plastik menjadi bahan bakar minyak menggunakan kondensor bertingkat dan pendingin kompresi uap,” INVOTEK J. Inov. Vokasional dan Teknol., vol. 17, no. 2, 2017.

H. Nurdin, Y. Fernanda, and M. Handayani, “Analysis of Tensile Strength the Fiber Bagasse Particles Board with Resin Adhesives,” J. Teknomekanik, vol. 1, no. 1, pp. 1–5, 2018.

M. N. SyaFe’i, “Rancang Bangun Simulasi Turbin Air Cross Flow,” J. Pendidik. Tek. Mesinn, 2016.

Adly Havendri and H. Lius, “Perancangan Dan Realisasi Model Prototipe Turbin Air Type Screw ( Archimedean Turbine ) Untuk Pembangkit Listrik Tenaga Mikrohidro Dengan Head Rendah Di Indonesia,” J. Tek. Mesin, vol. 1–7, no. 31, p. 2, 2009.

P. T. D. Rompas, “Analisis Pembangkit Listrik Tenaga Mikrohidro (Pltmh) Pada Daerah Aliran Sungai Ongkak Mongondow Di Desa Muntoi Kabupaten Bolaang Mongondow,” J. Penelit. Saintek, vol. 16, no. 2, pp. 160–171, 2011.

C. Penche, Layman’s Guidebook “on how develop a small hydro site.” European Small Hydropower Association (ESHA), 1998.

A. M. Harahap, “Analisis Numerical Aliran Fluida pada Rumah Water Vortex Turbine dengan Water Depth 200 mm dan Inlet Velocity 0.20 m/s Menggunakan Aplikasi Ansys Fluent Versi 16.2,” Universitas Negeri Padang, 2017.

F. Tuakia, Dasar-dasar CFD Menggunakan FLUENT. Bandung: Informatika, 2008.

Downloads

Published

2018-12-16

How to Cite

Purwantono, P., Sidiq, A. H., Irzal, I., & Refdinal, R. (2018). Numerical Analysis of Fluid Flow on Cross Flow and Kaplan Turbine Prototype. Teknomekanik, 1(2), 43–47. https://doi.org/10.24036/tm.v2i1.1972

Issue

Vol. 1 No. 2 (2018): Regular Issue

Section

Research Articles